Transport is the shortest phase of the poultry production cycle and one of the most expensive when it goes wrong. A chick that arrives dehydrated, a broiler with a bruised breast, a pallet of eggs that loses four percent to cracks — none of these problems is visible at the loading dock. They surface later, as higher first-week mortality, as downgraded carcasses at the processing plant, or as a claim from the customer who opened the container.
There are three transport streams on a modern poultry operation, and each one fails for a different reason. Day-old chicks are lost to cold, crowding and long transit. Live adult birds are lost to rough handling and heat. Eggs are lost to impact, vibration and temperature swing. Equipment built around those specific failure modes removes most of the risk before anyone lifts a crate.
Jinlong — Jiangsu Longlong Plastic Products Co., Ltd. — has been manufacturing HDPE poultry transport crates, shifting crates and egg transport systems in Yancheng, Jiangsu Province, China since 2017, supplying hatcheries, layer farms, breeder farms and integrators in Europe, Africa, Southeast Asia, the Middle East and Australia. This guide sets out the practices we recommend to customers, together with the equipment we build for each stream.
1. Chick Transport: The Box and the Load Plan Do Most of the Work
A day-old chick has no ability to regulate its own body temperature, no fat reserve worth speaking of, and roughly 48 to 72 hours of viability before dehydration becomes irreversible. Everything that happens between the hatchery and the brooding house is therefore a thermal and ventilation problem first, and a logistics problem second.
The Jinlong TB15 chick transport box is built around that reality: a four-compartment HDPE box holding 80 to 100 chicks, with an optional lid, ventilated on all four walls and through the lid panel, and stackable without deforming the boxes underneath.
The four-compartment layout is the detail that matters most. Chicks under stress move toward corners and edges and pile up. In one large open box the pile has the full floor behind it, and the birds at the bottom take the weight of every bird that joins it — which is how smothering and leg damage begin. Partitions split the load into four smaller groups, so each pile is shorter, the pressure per bird is lower, and the groups are easier to count, inspect and cull at placement.
Ventilation in a stack is not the same as ventilation in a single box. Once boxes are stacked six or seven high on a pallet, a large share of each box's side surface is covered by the box above and below it. Air has to reach the stack, not just the truck. Stagger pallets so that no stack sits flat against the vehicle wall, keep a gap between rows, and never throw a tarpaulin over the load to "keep them warm" — that is the fastest way to turn a cool morning into a suffocated batch.
Temperature. Keep the box-level environment at roughly 24 to 28 °C with 50 to 65 percent relative humidity, and measure it at the box, not at the cab. Direct sun on an unprotected stack can push internal temperature far above ambient within minutes, which is why loading before 10 a.m. or after 4 p.m. is standard practice in hot regions and why a light-coloured cover over the load is worth the effort.
Loading density. The rated capacity is 80 to 100 chicks, and the two ends of that range exist for a reason: load at the low end (around 80) in hot weather, on journeys longer than eight hours, and with smaller or later-hatch chicks; load at the high end only in cool, dry conditions with short runs. Count the chicks. Volume is a poor proxy, and a box that is 20 percent overfilled loses far more than 20 percent of its ventilation.
2. Adult Bird Transport: Handling Discipline, Not Just Hardware
Moving live birds — spent hens, culls, pullets being transferred between houses, or broilers going to processing — is the part of the job where welfare risk and product value are the same number. Bruised breasts, broken wings and dead-on-arrival birds are all deductions at the plant.
The Jinlong SC07 chicken shifting crate measures 74 × 55 × 29.8 cm, is moulded in HDPE with open mesh sides for airflow, and is rated to 16 kg. The rating is a weight limit, not a bird count: depending on bird size that is typically five to eight birds, and the number has to be recalculated for every load. Weigh the first filled crate once and use that count as the standard for the rest of the run.
Loading procedure. Catch the bird by the body with both wings held against it — never by a single wing, the neck or a leg, which is how dislocation and haemorrhage happen. Carry with both hands, place the bird in the crate, and close the lid before moving to the next. Do not throw birds into a crate from the aisle; a drop of half a metre is enough to break a wing. Work in dim light, in the cool part of the day, and keep the catching crew and the loading crew separated so that nobody is stacking crates over a bird still being handled.
Loading and unloading sequence. Position empty crates on the vehicle first, then load from the far end toward the door, and secure each tier as it is completed rather than strapping the whole load at the end. On arrival, unload in reverse order so that the crates that spent longest in the vehicle come out first. Every minute of standing time on a hot dock is a minute of heat accumulation in the middle of the stack.
Minimising injury. Inspect every crate before it goes on the truck: broken slats, sharp moulded edges and cracked lids all cause damage that shows up as skin lesions at the plant. Retire damaged crates instead of patching them. Do not stack beyond the height at which the bottom crate visibly bows, and never compress a load with a strap that runs across the birds rather than the crate frame.
Biosecurity. Crates are the most-shared, least-cleaned object on most farms, and they are an efficient vector for everything from Salmonella to lice. Wash in three stages — pre-rinse to remove organic matter, detergent wash, then a registered disinfectant at the correct contact time — and let the crates dry completely before they are stacked. Dry matters as much as disinfected: residual water inside a slat joint is exactly where biofilm survives the next wash. Keep dirty and clean crates physically separated at the wash bay, use dedicated crates per farm where possible, and treat the loading dock as a controlled boundary with a footbath and a change of footwear.
3. Egg Transport Systems: Individual Cells, Rigid Pallets, Controlled Temperature
Egg losses are cumulative and quietly expensive: a two to twelve percent breakage rate is common across the industry, and every broken egg is a lost sale plus a cleaning cost. Breakage is rarely caused by one bad drop. It is caused by thousands of small relative movements — egg against egg, tray against tray, pallet against truck bed — over a journey of several hundred kilometres.
The Jinlong ECS egg transport system is designed to remove that movement. Tray modules, a rigid pallet base and interlocking dividers form one load that behaves as a single unit rather than a stack of loose trays, with a working capacity of 10,800 eggs per set. The system has been field-validated on journeys of more than 1,000 km with low breakage rates, and is supplied in both manual and robot-automation configurations for farms that load and unload at scale.
For farm-level collection and shorter runs, the Jinlong EC01 egg shifting crate holds 360 eggs in individual compartments at 68 × 37 × 36 cm, in virgin HDPE, stackable when full and nestable when empty. The EC02 foldable egg crate carries the same 360-egg capacity but collapses when empty, cutting return shipping volume by up to 65 percent — the right choice for contract growers who run crates back from a packing centre every day. The EC03 (180 eggs) covers medium-scale layer and duck-egg operations where a 360-egg crate is too heavy for one person to handle comfortably.
Breakage prevention, in practice:
- · Fill the crate completely. A partly filled crate lets eggs slide and collide; the empty space is the damage.
- · Respect the stack limit and strap every tier. Unsupported double-stacking is the single most common cause of pallet-level collapse.
- · Keep eggs out of direct sun and away from the exhaust side of the vehicle.
- · Hold table eggs at roughly 10 to 15 °C. Hatching eggs have their own narrow band — usually 15 to 18 °C with high humidity — and should never share a load with chilled table eggs.
- · Load over the axles, not over the tail. The rear of a truck has the largest vertical amplitude.
- · Inspect crates for cracks and missing cell walls before loading, and replace rather than repair.
4. Transport Vehicle Requirements
The best crate on the market cannot compensate for a truck that vibrates or a load that is not secured. Five things decide whether the equipment performs.
Suspension is the first. Air suspension reduces the vertical shock that reaches the load; well-maintained leaf springs are acceptable on good roads, but worn bushes and uneven tyre pressure turn a smooth highway into a continuous impact. Check tyre pressure before every run, and keep the load centred over the axles rather than distributed to the rear.
Temperature control comes second, and it is stream-specific. Chick vehicles need ventilation and shade, not refrigeration — air must move through the load, and the cab temperature is irrelevant to the chicks in the middle of a stack. Egg vehicles need temperature hold, with the set point recorded at loading and checked at delivery. Live-bird vehicles need airflow above all, with no dead zones behind the last row of crates.
Third, ventilation paths. Air enters at the front of the load space and leaves at the rear; if the load is packed solid from wall to wall, it will not. Leave a channel down each side and a gap between pallet rows, and keep roof vents clear of the stack height.
Fourth, load securing. Strap every tier to the vehicle structure, not to the tier below it, and use load bars or a headboard so nothing can slide forward under braking. A load that shifts even 10 cm during a stop is enough to crack the bottom layer of an egg pallet.
Fifth, route and timing. Leave early or late, avoid the midday heat, keep stops to the minimum the law requires, and pre-drive the last section of road if it is rural. Give the driver a one-page brief: what is on board, the temperature target, the maximum standing time, and who to call if the vehicle breaks down. The brief is cheaper than the load.
5. Pre-Transport Checklist
Run this checklist before every load. It takes ten minutes and it is the cheapest insurance in the operation.
6. Post-Transport Recovery: The First 24 Hours
Arrival is not the end of the journey; it is the point at which the bird or the egg starts paying for it. Handled well, a stressful trip costs a few days of growth. Handled badly, it costs the batch.
For chicks, unload immediately and put water in front of them before anything else. The Jinlong DT31 drinker base — a 27 cm HDPE base with 5.5 cm legs, compatible with standard water bottles — keeps the drinking trough above the litter line, so water stays clean and chicks do not have to compete with bedding to reach it. Offer electrolytes or a vitamin mix for the first hours after a long or hot journey.
Feed follows within the first hour, not the first day. The Jinlong AA-8 turbo chick feeder holds 5 kg, is designed for day-old chicks through 15-day broilers, and combines an adjustable stand with a lid — which is what keeps feed out of the litter and out of reach of contamination in the first week.
Then hold the brooding environment steady: around 32 to 34 °C at chick level for the first days, 60 to 70 percent relative humidity, and a long light period so that chicks can find feed and water. Resist the temptation to raise temperature further to "help" stressed chicks; dehydrated birds need water and access, not more heat.
Measure the result rather than assuming it. Crop fill is the fastest field indicator: a commonly used benchmark is roughly 80 percent of chicks with a full crop by 8 hours after placement and around 95 percent by 24 hours. Record dead-on-arrival percentage, 24-hour mortality, seven-day mortality and water intake for every load, and compare each load with your own baseline rather than an industry average. A batch that sits 0.5 percent above baseline in the first week is telling you something about the journey, not about the hatchery.
For adult birds, give one to two hours of rest in dim light before feed, with water available throughout, then check the load for injuries and culls and record them against the farm of origin. For eggs, move the pallets into the target storage temperature as quickly as possible and let them stabilise before grading — condensing humidity on a cold shell is the start of a storage problem.
7. Regulatory Considerations
Animal transport is one of the more heavily regulated parts of the poultry business, and the rules differ sharply by market. What follows is a map, not legal advice: confirm every requirement with the competent authority in your destination market before you ship.
In the European Union, Council Regulation (EC) No 1/2005 governs the protection of animals during transport. It covers transporter authorisation, certificates of competence for drivers and attendants, vehicle approval, journey logs for longer journeys, and limits on journey duration together with specified rest, water and feed intervals. Day-old chicks are treated as a special case with a short journey limit — generally around 24 hours — precisely because they dehydrate quickly.
In the United States, the federal 28-Hour Law (49 U.S.C. § 80502) requires that animals be unloaded for feed, water and rest at least every 28 hours during rail or road transport, and state-level animal welfare rules apply on top of it. Movement of hatching eggs and chicks is also affected by flock health programmes and, for imports, by USDA APHIS requirements.
For international shipments, expect a veterinary health certificate, an import permit from the destination country, and compliance with the WOAH Terrestrial Animal Health Code standards on animal welfare in transport, in addition to any airline-specific live animal acceptance rules. Air transit for day-old chicks is usually measured in hours, not days, and airline acceptance rules on box type and ventilation are strict.
Build one documentation folder per consignment and keep it with the driver: journey log, health certificate, import permit, vehicle approval, driver competence certificate, consignment note and an emergency contact sheet. In an inspection, the paperwork is what converts a delay into a routine check.
8. Conclusion: Transport Is an Equipment Decision as Much as a Driving One
Most transport losses are decided before the vehicle moves. A chick box with four compartments instead of one, a shifting crate rated by weight rather than by guesswork, an egg system that behaves as a single rigid unit instead of a stack of trays, a load plan that leaves air where air is needed, and a ten-minute checklist at the dock — these are engineering choices, and they are cheaper than the losses they prevent.
Jinlong supplies the complete transport range from one factory in Yancheng: TB15 and SC-series chick and poultry crates, SC07 shifting crates, EC01, EC02 and EC03 egg crates, and the ECS long-distance egg transport system, together with the DT31 drinker and AA-8 feeder that get a batch started properly on arrival. If you are specifying equipment for a new route, talk to our team with your volumes, journey lengths and climate, and we will match the crate specification to the run rather than the other way round.
How many chicks fit in a poultry transport crate? The Jinlong TB15 holds 80 to 100 day-old chicks in four compartments. Load at the lower end for hot weather or journeys over eight hours, and never exceed the rated capacity.
What temperature should chick transport be kept at? As a working range, 24 to 28 °C at box level with 50 to 65 percent relative humidity, measured inside the load rather than in the cab, with the stack shaded from direct sun.
Can plastic egg crates be reused? Yes. Virgin HDPE crates are designed for repeated cycles: pre-rinse, detergent wash, disinfect at the correct contact time, then dry completely before stacking. Avoid damaged crates for any load that will travel more than a few kilometres.
How do I reduce dead-on-arrival losses? Control the three variables in order: temperature and ventilation, loading density by weight, and time in the vehicle. Then measure the outcome — DOA percentage and first-week mortality per load — so that any change in performance can be traced back to a specific stage.
Post time: Nov-16-2026